المنتجات

اكتشف تشكيلتنا الكاملة من الأصباغ وكيماويات البناء وأنظمة العزل والأدوات.

Shop

عرض 61–80 من أصل 147 نتيجةتم الفرز حسب الأحدث

  • Betek Mesh Dropper Profile (PVC) 2.5 m

    Betek Mesh Dropper Profile (PVC) 2.5 m

    2.5 m PVC dropper corner profile. Used in the top edges of building openings like windows and doors. Dropper enables the water on the surface to flow directly down without penetrating into the cores of doors and windows. Packaging: 20 units – 50 m

  • Betek Mesh Joint Gap Profile (PVC) 3 m

    Betek Mesh Joint Gap Profile (PVC) 3 m

    3 m PVC joint gap profile. Used in the transitions of joint gaps on the thermal insulation plates. Saves labor and time, and prevents workmanship errors thanks to the glass-fiber mesh glued on the profile. Offered in two different models as 3 cm and 5 cm with 1.6 cm depth. Packaging: 10 units – 30 m

  • Betek Subbasement Profile (Aluminum) 2.5 m

    Betek Subbasement Profile (Aluminum) 2.5 m

    2.5 stainless steel subbasement profile. Used to ensure smoothness at the lower edge of thermal insulation system and create the vertical finish when required. Offered in models suitable for 3-4-5-6-7-8 cm plates. Packaging: 10 units – 25 m

  • BETEKTECT BRICK DOWEL (PLASTIC NAIL)

    BETEKTECT BRICK DOWEL (PLASTIC NAIL)

    In Betektect Thermal Insulation System, these are used to fasten Betektect Thermal Insulation Plates to the surfaces and to protect the system against wind vacuum.

    Provides higher strength in perforated bricks and perforated surfaces with its special nibbed design.

    Depth of fastening: > 7 cm
    Depth of hole: > 8 cm
    Diameter of drill: 10 mm
    Diameter of dowel head: 6 cm
    Length: 13.5 / 15.5 cm
    Packaging: 200 units

  • BETEKTECT CONCRETE DOWEL (STEEL NAIL)

    BETEKTECT CONCRETE DOWEL (STEEL NAIL)

  • BETEKTECT GAS-CONCRETE DOWEL (PLASTIC NAIL)

    BETEKTECT GAS-CONCRETE DOWEL (PLASTIC NAIL)

    In Betektect Thermal Insulation System, these are used to fasten Betektect Thermal Insulation Plates to the surfaces and to protect the system against wind vacuum.

    Provides higher strength in gas-concrete surfaces with its special nibbed design.
    Depth of fastening: > 6 cm
    Depth of hole: > 12 cm
    Diameter of drill: 10 mm
    Diameter of dowel head: 6 cm
    Length: 11 – 14 cm
    Packaging: 200 units

  • BETEKTECT OSB DOWEL (No Nail)

    BETEKTECT OSB DOWEL (No Nail)

    In Betektect Thermal Insulation System, these are used to fasten Betektect Thermal Insulation Plates to the surfaces and to protect the system against wind vacuum.

    Exclusively manufactured to be used in Osb and similar prefabricated surfaces. Since the diameter, size of the nail has to change depending on the surface,

    Betektect OSB Dowel has no nail.
    Diameter of dowel head: 6 cm
    Length: 2.5 cm

  • BETEKTECT ROCKWOOL DOWEL STAMP

    BETEKTECT ROCKWOOL DOWEL STAMP

    In Betektect Thermal Insulation System, these are used to fasten Betektect Thermal Insulation Plates to the surfaces and to protect the system against wind vacuum.

    Can be used with all Betektect Dowels in thermal insulation plate applications in exterior thermal insulation systems. Provides excellent grip by extending compression area of the dowels.

    Diameter of dowel head: 9 cm

  • BETEKTECT STANDARD DOWEL (PLASTIC NAIL)

    BETEKTECT STANDARD DOWEL (PLASTIC NAIL)

    In Betektect Thermal Insulation System, these are used to fasten Betektect Thermal Insulation Plates to the surfaces and to protect the system against wind vacuum.

    Used at concretes, solid bricks, perforated bricks, gas concretes and solid and perforated blocks made of light concrete.

    On gas concrete surfaces, use of gas concrete dowel, and on brick surfaces, use of brick dowel is recommended.

    Depth of fastening: > 3 cm
    Depth of hole: > 4 cm
    Diameter of drill: 8-10 mm
    Diameter of dowel head: 6 cm
    Length: 9.5 / 11.5 / 13.5 / 15.5 cm
    Packaging: 200 units

  • Impermeability Band

    Impermeability Band

    15 x 8 mm and 18 m length, acrylic processed structure, water repellent insulation band. It is used in high risky water leak points of roof fringes, window frames and sills on thermal insulation system

  • Betek Aquaset

    Betek Aquaset

    An acrylic copolymer resin-based, water-based, single-component, ready-to-use, elastic, white (colorable) waterproofing spread material that can be applied on all types of surfaces easily.

    – Ready to use.
    – Easy-to-apply semi-fluid. Covers tough surfaces easily. Low labor cost.
    – Elastic. Elongates 600% after 24 hours at 23°C in 1 to 1.5 mm thickness.
    – Adheres perfectly to all types of building materials.
    (Adhesion strength on mineral based surfaces: 7.15 kgf / cm2).
    – Maintains its elasticity in temperature differences (476% at 70°C, 397% at -17°C).
    – Resistant against weak chemicals.
    – Enables the surfaces to breathe.
    (Water vapor permeability: 27.6 g/m² day after 24 hours at 23°C and 65% relative humidity)
    – Tensile strength: (23°C – 65% RH) 24.5 kgf / cm2 after 24 hours, 55 kgf / cm2 after 72 hours.
    – Does not contain any solvents.
    – Decorative. Can be colored with Betekmatic tubes even though it is produced white (only 4-5 shades) or painted using a water-based paint with the same elasticity

  • Betek Fibrious Aquaset

    Betek Fibrious Aquaset

    Betek Fibrious Aquaset is a ready-to-use, polypropylene micro fiber-added, white, liquid membrane waterproofing material that is developed for regions named as risky in waterproofing.

    – Enables applying waterproofing materials easily on top of cracks that occurred on old surfaces in time due to thermal reasons or settling.
    – Removes the need for a new application by preventing the applied waterproofing system to be damaged due to the possible future macro-cracks.
    – Provides more effective resistance against mechanical impacts with the additional strength that it gains thanks to the polypropylene micro fiber in its formula.
    – Does not get affected from cold-hot differences. (-20°C ± 80°C)
    – Can be painted only using a water-based paint with the same elasticity.
    – Prevents the growth of bacteria thanks to the biocides in its formula.
    – Provides perfect adhesion to mineral-based surfaces, wood and non-anodized metal surfaces.

  • Betekstop

    Betekstop

    Cement-based, single-component crystallized waterproofing mortar with capillary effect that can be applied from negative and positive sides with polymer additives containing special type of cement and filling to provide solutions in situations like paint blistering and plaster flaking.

    – Prepared by mixing with water only. Applied easily with brush or trowel.
    – Used securely in waterproofing of horizontal and vertical surfaces both from negative and positive sides.
    – Applied securely to all kinds of cement-coated surfaces, and all old and new brute concrete surfaces.
    – Offers non-abrasive, non-corrosive full water insulation that can’t be passed and detached from the surface.
    – Provides resistance against mechanical and chemical impacts. Protects the iron and concrete against abrasive effects of water.

  • Polycrete

    Polycrete

    A cement- and acrylic-based, two-component, fully elastic waterproofing material.

    – Highly adherent.
    – Fully flexible and watertight.
    – Resistant against mechanical impacts due to the flexible coat that it forms.
    – Preserves its quality even in possible future capillary cracks on the application surfaces (up to 0.1 mm).
    – Forms a permanent layer without any joints and attachments.
    – Permeable to water vapor.

  • Bitumfleks

    Bitumfleks

    Modified bitumen emulsion-based, single-component, ready-to-use, solvent-free, water insulation spread material with high adhesion strength.

    – Ready-to-use in fluid consistency.
    – Provides high adherence to dry and moist surfaces.
    – Prevents weathering, dusting and bloating on interior surfaces by providing water- and damp-proofing.
    – Continues to protect the structure against water and damp without losing its watertight quality in possible future structural capillary cracks.
    – Does not get affected from temperature differences when it gains its full strength (-15°C – +80°C).

  • BETEK FAYFIKS SL-40

    BETEK FAYFIKS SL-40

    ملاط ذو أساس أسمنتي، ذاتي الاستواء، يُستخدم لإنشاء طبقة تحتية ناعمة وصلبة وخالية من الغبار، وذلك عن طريق التخلص من التفاوت في مستوى الاستواء من على السطح.

    ملاط ذو أساس أسمنتي، ذاتي الاستواء، يُستخدم لإنشاء طبقة تحتية ناعمة وصلبة وخالية من الغبار، وذلك عن طريق التخلص من التفاوت في مستوى الاستواء من على السطح.

     

    مناطق الاستخدام

    يُستخدم بصفة خاصة قبل وضع طبقة الأرضيات الخارجية الزخرفية مثل البولي فينيل الكلوريد (PVC)، والباركيه المكون من طبقات، والفينيل، والباركيه، والموكيت، والمواد المشابهة لذلك؛ وقبل تركيب السيراميك والأرضيات والرخام، ولسد الفجوات الموجودة في الأسطح الخرسانية أو الأرضيات الخرسانية الجاهزة، بالإضافة إلى إصلاح وتسوية الأسطح الخرسانية القديمة والأسطح المستخدم عليها طبقة تسوية (سكريد).

     

    الخواص

    • يوفر الوقت والجهد، إذ يتيح تغطية مناطق كبيرة بسرعة.
    • يُستخدم لتغطية الأماكن التي يجب إتاحتها لعبور المارة في فترة وجيزة، وذلك بفضل قدرته على زيادة قوة الأرضيات بسرعة.
    • فيستطيع المارة العبور على الأرضيات بعد 24 ساعة.
    • طبقة نهائية لتسوية الأرضيات؛ يتماشى مع جميع أنواع المواد اللاصقة نظرًا لاعتماد تركيبته على الأسمنت وخلوه من المواد السامة.

     

    المواصفات الفنية

    اللون                                          رمادي

    كثافة خليط المسحوق           1.35 ± 0.1 جم/سم³

    مقاومة الضغط                                                      ≥ 20 نيوتن/ملم²

    مقاومة الالتواء                                                      ≥ 6 نيوتن/ملم²

    الوقت اللازم للاستخدام                    15 دقيقة

    مدة الصلاحية بعد المزج                              20 دقيقة

    الفترة اللازمة قبل السماح بعبور المارة 6 – 8 ساعات لاحقة

  • BETEK FAYFIKS TA 10

    BETEK FAYFIKS TA 10

    A cement based adhesive with high slip resistance, extended open waiting time and high performance. Conforms to TS EN 12004 Standard class C1TE.

    APPLICATION AREAS
    Can be safely used for laying ceramic, tile and similar coatings in swimming pools, water tanks, bathrooms, toilets and kitchens. Recommended to be applied on cement-based plaster, screed and concrete surfaces.

    FEATURES
    Fayfiks TA 10 easily adheres to the application surface thanks to its special materials and does not slip; gives tile and ceramics the ability to be processes thanks to its flexing tolerance. It is resistant to temperature differences and has excellent adhesion performance on exteriors. It is easy to comb, and its long working time saves time and labor.
    TECHNICAL SPECIFICATIONS

    Color Light grey

    Dry Powder Density 1.35 ± 0.1 g/cm³

    Water Blending Ratio 5.5 – 6.5 L

    Container Drying Time (pot life) Approximately 3 hours

    Open Waiting Time 30 minutes

    Joint Application Time After 24-48 hours

    Fire Response Class A1

    The above specified figures are valid for 23 ± 2 °C temperature and 50 ± 5% relative humidity. The time shortens at hotter conditions and extends at colder conditions.

  • BETEK FAYFIKS TA 15

    BETEK FAYFIKS TA 15

    A cement based granite and marble adhesive with polymer additives, high performance, improved flexibility and sliding resistance, and extended open waiting time. It is an flex and highly thixotropic product which can easily be combed.
    Conforms to TS EN 12004 Standard class C2TE.

    APPLICATION AREAS
    Used for affixing of materials like granite, marble, ceramic, natural stone, large size ceramic, glass mosaic, porcelain ceramic on interiors and exteriors. Recommended to be applied on cement-based plaster, screed and concrete surfaces. Suitable for use in areas such as hospitals, schools and business centers with heavy pedestrian and load traffic. Suitable for use of heavy materials like marble and granite in vertical and horizontal surface applications. Suitable for use in wet places such as Turkish baths, saunas and pools.

    FEATURES
    Fayfiks TA 15 easily adheres to the application surface thanks to its special materials and does not slip; gives tile and ceramics the ability to be processes thanks to its flexing tolerance. It is resistant to temperature differences and has excellent adhesion performance on exteriors. It is easy to comb, and its long working time saves time and labor.
    TECHNICAL SPECIFICATIONS

    Color Gray

    Dry Powder Density 1.4 ± 0.1 g/cm³

    Container Drying Time (Pot Life) Approximately 2 hours

    Water Blending Ratio 7.0 – 7.5 L

    Open Waiting Time 30 minutes

    Joint Application Time Minimum 24 hours

    Adhesion Strength ≥ 1.5 N/mm²

    Slip ≤ 0.5 mm

    ire Response Class A1

    The above specified figures are valid for 23 ± 2 °C temperature and 50 ± 5% relative humidity. The time shortens at hotter conditions and extends at colder conditions.

  • Fayfiks

    Fayfiks

    A cement-based tile and ceramic adhesive with increased horizontal slip resistance.

    Increased horizontal slip resistance.

  • Bepermo

    Bepermo

    – Powder admixture without any white chloride that is used to create a high quality water repellent surface in all types of plaster, screed and concrete works.
    – Ensures water tightness by preventing the formation of capillary cracks and gaps within the plaster, screed and concrete
    – Creates surfaces with high water retention
    – Removes the dampening property of the water particles
    – The lime that you will use in the plaster works has no negative impact on Bepermo
    – Improves the quality and strength by increasing the formation of air in the fresh plaster and concrete mortar

تحدث معنا